Accelerate Breakthrough Research with Intuitive Sample Preparation

  • There are no suggestions because the search field is empty.

SUPPORT / ARTICLES

What Is Randall Extraction?

Randall extraction (also called the Soxtec or submersion method) is a faster, modified version of the classic Soxhlet technique that determines crude fat content by immersing samples directly in boiling solvent rather than repeatedly washing them with condensed solvent vapor.

The Randall Extraction Process

Developed as an accelerated alternative to Soxhlet, the Randall method was introduced in the mid-20th century (with widely cited refinements around 1974) and cuts total extraction time down to roughly 30–60 minutes compared to several hours for traditional Soxhlet runs. The technique unfolds in three distinct, sequential stages:

  • Boiling: The sample, held in a porous thimble or filter, is fully submerged in boiling solvent, which dissolves lipids or analytes far more efficiently because solubility is higher in hot solvent than in the cool-to-warm solvent used during standard Soxhlet cycling.

  • Rinsing: The thimble is raised out of the boiling solvent bath and washed with fresh, condensed solvent, mimicking the classic Soxhlet reflux cycle to remove residual analyte.

  • Recovery: The solvent return valve is closed so condensed solvent is diverted away and collected for reuse (recovery efficiencies up to about 80% have been reported), leaving behind the concentrated, solvent-free extract for gravimetric analysis.

Because fat content is measured by directly weighing the recovered residue, Randall is classified—like Soxhlet—as a direct gravimetric method, and it is also used following acid hydrolysis to determine total fat in food and feed samples. 

Randall vs. Soxhlet Extraction

The core distinction lies in how the sample contacts the solvent: Soxhlet relies on cyclical washing with fresh condensed solvent, while Randall submerges the sample directly in a single, continuously boiling solvent batch.

Feature

Soxhlet

Randall

Solvent contact

Repeated washing with condensed (cool/warm) solvent vapor cycles

Direct immersion in boiling solvent, then rinsing

Extraction time

Several hours per run

As fast as 30 minutes to ~1 hour, up to 4x faster

Process stages

Continuous siphon/reflux cycling

Three discrete steps: boiling, rinsing, recovery

Solvent recovery

Possible but less structured

Built-in recovery stage, up to ~80% efficiency

Best suited for

Wide range of matrices, considered the gold-standard reference method

User-friendliness and lower solvent consumption, especially for routine fat analysis

Industry references note that "whereas Soxhlet is a proven method for all kinds of samples, Twisselmann and Randall are preferable for user-friendliness and solvent consumption".

Other Common Extraction Approaches

Beyond Soxhlet and Randall, analytical chemists rely on several other solid-liquid and liquid-liquid techniques depending on the matrix and desired throughput. Traditional approaches include maceration and percolation, while modern, energy-efficient alternatives have emerged to shorten extraction times further:

  • Liquid-liquid extraction: Uses a separatory funnel to partition dissolved compounds between two immiscible solvent layers, typically one aqueous and one organic.

  • Ultrasound-assisted extraction: Applies sound energy to disrupt cell matrices and accelerate solvent penetration, reducing extraction time versus classical methods.

  • Microwave-assisted extraction: Uses microwave energy to rapidly heat solvent and sample together, often cutting extraction time significantly.

  • Pressurized liquid (solvent) extraction: Applies elevated temperature and pressure to keep solvent liquid above its boiling point, increasing extraction efficiency and speed.

Supercritical fluid extraction: Employs a supercritical fluid (commonly CO2) as the extraction medium, offering tunable selectivity and easy solvent removal. 

Applications in Routine Fat and Lipid Determination 

Randall extraction sees its widest use in official crude fat and total fat determinations for animal feed, cereal grains, forages, and a range of foodstuffs, largely because it has been formally adopted into AOAC collaborative methods.

Animal Feed and Cereal Grain Analysis

The most extensively validated application of Randall extraction is crude fat determination in animal feed, cereal grains, and forage (plant tissue), where AOAC-recognized collaborative studies confirmed its reliability using both hexane and diethyl ether as solvents. This method, officially designated AOAC 2003.05, is applied broadly across the feed industry to verify nutritional labeling and formulation consistency for livestock feed. A parallel collaborative study extended the Randall approach to cereals, cereal-based products, and animal feeding stuffs, measuring both "crude fat" (directly extractable) and "total fat" (after acid hydrolysis) across 15 laboratories in nine countries.

Oilseeds, Dairy, and Meat Products

Beyond grains and feed, Randall extractors are routinely applied to oilseeds and nuts, dairy and milk-based products, various meats and meat-related goods, and fish and seafood, reflecting the method's versatility across high-fat food matrices. In these settings, laboratories use the technique for raw material inspection to confirm fat content meets specification before processing, and for in-process monitoring during production stages such as mixing or formulation. The method is also applied to cocoa and chocolate products, where accurate fat quantification is critical for both nutritional labeling and process quality control.

Total Fat via Acid Hydrolysis

Many food matrices contain lipids that are chemically or mechanically bound within the sample matrix and are not accessible to solvent alone; in these cases, Randall extraction is paired with a preliminary acid hydrolysis step using hydrochloric acid to liberate bound fats before extraction. This combined hydrolysis-Randall approach is widely used for total fat analysis in foodstuffs including cereals and cereal products, and is required for samples with relatively high fat content (at least 100 g/kg) where a preliminary extraction step is also necessary.

Quality Control and Adulteration Detection

Quality control laboratories rely on Randall-based fat analysis not just for compliance verification but also for detecting adulteration in high-value products such as specialty oils and dairy goods, where deviations from expected total fat content can signal quality issues. Specific applied protocols, such as crude fat determination in oatmeal following AOAC 2003.05, illustrate how the method is standardized for routine cereal-based product testing in commercial and regulatory labs. Because the technique also supports solvent recovery at efficiencies up to 80%, it has become the preferred routine method where labs must balance analytical rigor with cost and solvent-use considerations across high sample-throughput environments. 

Get Exclusive Lab Deals Straight to Your Inbox

Limited-time offers, special pricing, and practical lab insights in our newsletter

Contact Us

If you need support from one of our technicians, please fill out our Contact Help Support form and we will respond as quickly as possible! For all other enquiries, please use this general contact form.

 

USA 888.838.7300
Other 978.838.7300
978.838.2786